{{product['name']}}

TLR-1 HL
Light body x1
Adapter x4 types (one type is already attached to the light body)

Size 90 x 37 x 37mm
Weight 90g
Material Aluminum alloy
Surface treatment Hard anodized
Light intensity: Approximately 1000 lumens
Lighting mode constant, momentary, strobe
Batteries used: CR123A batteries x2 (sold separately)

Equipped with a large-diameter bezel and a high-luminance LED, it delivers one of the highest levels of light among handgun light replicas!
In addition to constant (always on) and momentary (intermittent lights), it is also equipped with a high-speed flashing strobe mode, making it an aggressive weapon light.

The lightweight and durable aluminum alloy body has a MILSPEC hard anodized finish with a rough matte texture that looks just like the real thing!

In addition to an under rail adapter compatible with handguns such as the Glock series, three types of adapters are included: ``20mm Picatinny Rail'', ``S&W TSW/99'', and ``Beretta 90-TWO''.

対応機種

Comes with 4 types of adapters.
Since the rail guide itself moves and pinches the underrail, there is almost no effect from differences in rail width between manufacturers. Compatible with all manufacturers.

■ GL
A general-purpose adapter for handgun underrails.
⇒Glock series such as G17/G18C/G19
⇒Other handguns with under rails

■ 1913
Adapter for 20mm Picatinny rail.
⇒20mm rail for M4, Scar, HK416, MP7, etc.
⇒20mm under rail equipped handgun such as M45A1, FNX45, etc.

■ TSW/99
⇒ Compatible with Smith & Wesson TSW & 99

■ 90two
⇒Compatible with Beretta 90-Two

High light output white LED

Among the hand gun light replica series that uses two batteries, it is characterized by a particularly high light output of approximately 1000 lumens.
The light beam is slightly diffused and can brightly illuminate a wide area.

*Due to the extremely bright amount of light, please never look directly at the light source.

Aluminum alloy & hard anodized

The body is made of lightweight and sturdy aluminum alloy.
Made of high-quality materials, it weighs only 90g for its size, so it won't be a burden when attached to the tip of a handgun or rifle.

The surface is hard anodized and hardened to give it a beautiful rough texture and matte texture, giving it a luxurious finish.

White markings are reproduced on the left and right sides of the main body, making it a cool accent!

*The notation and font of white markings may differ depending on the production lot.

How to insert batteries

Two CR123A batteries are used. (sold separately)

Raise the lever on the top of the rear of the main unit and open the battery cap.
Insert the two batteries according to the white markings and close the battery cap in reverse order.

*Please be sure to use new batteries. Old batteries or even new batteries that have been left unused for a long time may discharge and may not light up properly.

How to operate

Operate with the paddle switch on the rear of the main unit.

■ Constant
By tilting the switch to the left, it will switch constantly and the light will always be on.

■ Momentary
If you tilt the switch to the right, the light will turn on momentarily only while you continue to tilt it. When you release the switch, it automatically returns to the OFF position.

■ Strobe (high-speed flashing)
Switch to strobe mode by quickly operating the switch twice. Basically, it is used in momentary mode, but if you operate it properly, you can also use constant strobe mode.

How to attach to air gun

1. Loosen the mount adjustment screw on the left side of the main unit.
2. Push in the mount adjustment screw with your thumb and align it with the rail of the air gun.
3. Tighten the mount adjustment screw to secure it completely.

How to replace the adapter

1. Loosen the mount adjustment screw.
2. Remove the hex screw located next to the mount adjustment screw.
3. Pull out the adapter.