Ultraforce Airsoft Gun Cleaner Degreaser

Clean and protects your airsoft gun in one easy step.
Penetrates deep into rusted airsoft guns, freeing stuck parts and providing cleaning aids.
Provides long-lasting protection from rust. Removes oil spots, carbon, and grease.

A well-known deep-cleaning and degreasing spray for airsoft guns and firearms among wargame players and simulated gun enthusiasts.

1. Airsoft and Firearms Maintenance Grade:

This is the most common spray-type degreaser in the airsoft and high-pressure airsoft gun community, primarily used for cleaning carbon deposits and old oil from metal slides, barrels, and internal parts.

* Core Functions:

* Powerful Degreasing: Quickly washes away old lubricant, oil stains, carbon deposits, and impurity particles from parts with high-pressure spray.

* Protects Metal: Deeply cleans and removes rusted or stuck precision parts, leaving a long-lasting rust-preventive protective film.

* Safe and Material-Friendly: The formula is safe for the metallic paint and most polymers (plastics) of air guns, and will not easily cause embrittlement or fading even with slight contact.

* Quick-Drying: Utilizing a chlorine-free, CFC-free, highly volatile formula, it dries quickly after spraying without leaving any residue.

* Instructions for Use:

1. Pull up the flip-up nozzle for pin-point application.

2. Spray directly onto the receiver, slide rails, or inside the barrel to flush away dirt using high pressure.

3. After cleaning and drying, reapply air gun-specific silicone oil or grease.
* Precautions: This product is highly volatile and flammable. Do not store in environments exceeding 40°C (110°F) and keep away from fire. Usage:

When using Ultraforce Gun Action Cleaner Degreaser, the correct operating sequence is crucial. Because it's a powerful degreaser, it will wash away all the original lubricant inside the gun, so re-lubrication is necessary after cleaning to prevent wear and tear or leaks.

Below is a complete four-step tutorial on "Disassembly, Cleaning, and Re-lubrication":

🛠️ Tools Needed

* Ultraforce Cleaner Degreaser

* Milspec Silicon Oil / Spray for Air Guns

* Gear Grease / Teflon Grease (for gears and metal friction surfaces) for Air Guns

* Lint-free cleaning cloth, cotton swabs, gun cleaning strip

------------------------------

📝 Four Core Operating Steps

Step 1: Safety Check and Most Disassembly

1. Remove the magazine and empty the chamber, ensuring there are no BB pellets or gas inside the gun.

2. Perform a field strip to separate the slide, barrel assembly, and lower receiver.

3. Important Reminder: Please remove the hoop-up rubber ring and the O-ring seal inside the aircraft first. Although this degreaser is relatively safe, direct high-pressure spraying of strong chemicals can still cause rubber parts to dehydrate, harden, or swell.

Step Two: High-Pressure Spray Cleaning

1. Pull up the thin tube (flip-type nozzle) on the Ultraforce nozzle for precise positioning.

2. For the slide and metal parts: Align with the slide guide groove, recoil spring, and inside of the slide, and press the nozzle directly. Use the high-pressure spray to directly flush out carbon deposits, old black oil, and dirt (it is recommended to place newspaper or a cloth underneath to catch the dirty water). 3. For the lower fire control assembly: Spray directly into the crevices of precision metal parts such as the hammer and screws to wash away residual debris and old grease.

4. Allow to evaporate naturally: Let stand for about 1-2 minutes after spraying. This formula evaporates very quickly and will dry completely on its own, leaving no trace.

Step Three: Manual Detail Cleaning

1. Use a cotton swab dipped in a small amount of Ultraforce degreaser to carefully wipe the hard-to-reach areas that the gun cleaning strip cannot be directly cleaned.

2. Use a clean gun cleaning cloth to thoroughly wipe away any remaining dirt from the surface of the parts.

Step Four: Crucial! Reapply Lubricant
After degreasing, the metal surfaces are completely dry and unprotected; direct firing will cause severe wear.

1. Gas-tight rubber parts: Apply a small amount of pure silicone oil to the previously removed HOP-UP rubber rings and O-Rings for maintenance before reinstalling them.

2. Metal Friction Surfaces (Sliding Sleeves, Hammer Friction Points): Apply a thin layer of high-viscosity grease or Teflon grease to the guide rails and metal joints.

3. Exterior Protection: Lightly wipe the barrel and metal casing with a cloth dampened with a small amount of silicone oil to form a rust-preventive protective film.

------------------------------

⚠️ Safety and Usage Precautions

* Do not spray directly into the HOP-UP compartment: If degreaser residue remains on the HOP-UP rubber ring, it will cause the rubber ring to lose its grip, causing the BB pellets to drop or fail to hold.

* Keep away from fire and high temperatures: This spray is a highly flammable compressed gas. Do not use in smoking, spark-prone, or high-temperature environments.

* Ensure ventilation: The chemical gas is highly volatile. Always operate in a well-ventilated outdoor area with windows open.

Wargame 玩家與模擬槍械愛好者熟知的氣槍/槍械深層清潔除油噴劑
1. 氣槍與槍械保養級：
這是生存遊戲（Airsoft）與高壓氣槍圈中最常見的噴霧型去油劑，主要用於金屬滑套、槍管及內部零件的積碳與舊油清理。 

* 核心功能：
* 強效去油：以高壓噴射快速沖刷掉零件上的舊潤滑油、油漬、碳沉積及雜質顆粒。
   * 保護金屬：深入生鏽或卡住的精密部件進行釋放與清潔，並留下一層持久的防銹保護膜。
   * 安全不傷材質：配方對氣槍的金屬烤漆及多數聚合物（Polymer/塑料）安全，即使輕微接觸也不易造成脆化或褪色。
   * 快速乾燥：採用無氯、無氟氯碳化物（CFC free）的高揮發配方，噴灑後迅速乾燥且不留任何殘留物。
* 使用教學：
1. 將噴嘴上的翻轉式細管（Flip-up nozzle）拉起以進行精準噴射（Pin-point application）。
   2. 對準槍械機匣、滑套軌道或槍管內部噴灑，直接利用高壓將污垢沖洗出來。
   3. 清潔乾淨並擦乾後，必須重新補上氣槍專用的矽油或潤滑脂。 
* 注意事項：本產品具高度揮發性與易燃性，嚴禁存放在超過 40°C（110°F）的環境，並須遠離火源。